Greenheck Microprocessor Controller (474706 IOM) TAP v1.04 J Instrukcja Użytkownika Pobierz pdf (Strona 11)

DDC Controller for Tempered Air Products

Menu Overview

Press

Prg

Esc

to enter menus.

c. BMS Config

d. Service Settings

Service

Manufacturer

Service Password

Insert service

password (PW1): 0000

Service Password

Insert service

password (PW1): 0000

Manufacturer Password

Insert service

password (PW1): 0000

BACnet Read/Write

Function: Read

Update? Yes

*Cycle unit power to

confirm write command.

a. Working hour set

a. Configuration

c. Factory settings

c. Password/Defaults

b. Probe adjustment

Probe Adjust

pCOe number: 1

Offset Ch 1: 0.0

Offset Ch 2: 0.0

Offset Ch 3: 0.0

Offset Ch 4: 0.0

Digital Compressor

Minimum OFF: 1.0vdc

Minimum ON: 1.9vdc

Maximum: 5.0vdc

Delay OFF: 60s

Max Power Start: 120s

Hot Gas Controller

Integration: 300s

Band: 20°F

Unoccupied Mode Setup

Type: CycleSupplyFan

Source: Input ID6

TCP/IP SETUP

Instance: 77000

IP set by: DHCP

IP: 172.016.000.001

Subnet: 255.255.255.000

Gatewy: 192.168.001.001

Analog Input

Cold Coil Temperature

Input B03:

###.#°F

Offset: 0.0°F

Value: ###.#°F

Analog Output Conﬁg

Wheel

Channel: Y1

Action: DIRECT

Minimum: #.#vdc

Maximum: ##.#vdc

Cooling Controller

Integration: 300s

Band: 20°F

Reheat Setup

Will heater be used

for reheat during

dehumidification?

Reheat: Disable

Supply Reset Control

Integration: 1200s

Band: 10°F

Wheel Rotation Sensor

Alarm delay: 30s

(input ID3)

TCP/IP SETUP

DNS 1: ###.###.###

DNS 2: ###.###.###

Type: IP

Analog Input

Room Temperature

Input B04:

###.#°F

Offset: 0.0°F

Value: ###.#°F

Compressor Setup

# of stages: #

Rotation: LIFO

Reheat Setup 2

Will heater be used

for reheat along

with hot gas?

Heater: Disable

Heat/Cool Delay

Time delay between

heating, cooling &/or

economizer modes.

Delay: 180s

Temperature Scale

Select: Fahrenheit

Display Buzzer

Select: Disable

User Default

Insert new service

password (PW1): 0000

Unit BMS Control

Unit Start/Stop: Yes

Temp Setpoint: Local

Occupancy: Input ID6

BMS Conﬁguration

Protocol: None

BACnet Plugin? Yes

MAINTENANCE HOURS

SYSTEM

Run hours: 0000h

Set Point: 0000h

Reset to Zero? No

Unit Code

Select DDC configur-

ation code here.

Code: GWXXXXXXX00

Analog Input

Outside Temperature

Channel:B1

Type: NTC

Offset: #.#°F

Value: ##.#°F

Factory Setup

Consult Factory

Before Altering

Compressor Timers

Minimum ON: ###s

Minimum OFF: ###s

Between Stages: ###s

Hot Gas Setup

Hot gas reheat coil

minimum on/off

time: 10minutes

Damper Setup

Allow the dampers to

open for: 10 seconds

before starting the

fans.

Factory Settings

Save? No

Restore? No

User Default settings

Save? No

Restore? No

BMS Write Points

TempSetpoint: aaa.a°F

Start/Stop: Stop

Reset Alarms: No

Occupancy: Occ

MODBUS SETUP

Address: 1

Baudrate 9600

Analog Input

Outside Temperature

Input B01:

###.#°F

Offset: 0.0°F

Value: ###.#°F

Unit Expansion Comm

Field Card Settings

Baudrate: 19200

Stop bit: 2

Parity mode: NONE

Timeout: 300ms

Digital Input

Supply Fan

Channel: ID1

Action: OPEN

Delay: 0s

Open

Economizer Controller

Integration 300s

Band: 20°F

Econo ON/OFF times:

Minimum ON: 300s

Minimum OFF: 300s

Compressor Staging

Stage1: ON @ 50% OFF 0%

Stage2: ON @ 100% OFF 50%

Fan/Airﬂow Proving

Alarm delay: 30s

(inputs ID1 & ID5)

Hot Gas Flush Setup

Cycle: 30minutes

Duration: 1minutes

New Password

Insert new manufacturer

password (PW2): ####

MSTP SETUP

Instance: 77000

Baudrate 38400

MAC Addr: 0

MaxMasters: 127

MaxInfoFrames: 10

Analog Input

Discharge Temperature

Input B02:

###.#°F

Offset: 0.0°F

Value: ###.#°F

Unit Expansion I/O

Enable Expansion: No

Relay Output

Defrost

Channel: 1

Status: OFF

Supply Fan Cycling

Defrost setup

Fan off time: 5min

Fan on time: 30min

Heater Controller

Integration: 300s

Band: 20°F

Mod Hot Gas Setup

Minimum On: 4.0vdc

Maximum On: 10.0vdc

Fan Delay

Time delay between

starting of supply

& exhaust fans.

Fan delay: 15s

Initialization

DEFAULT INSTALLATION

Erase user settings

and install global

default values: No

b. I/O Configuration

All I/O points are included An example of each is shown.

d. Initialization

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 31 32

Komentarze do niniejszej Instrukcji

Brak uwag

Greenheck Microprocessor Controller (474706 IOM) TAP v1.04 J Instrukcja Użytkownika Strona 11

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Ekwipunek Greenheck Microprocessor Controller (474706 IOM) TAP v1.04 J